- Thread starter
- #81
pssstitsmike
Well-Known Member
- 167
- 105
Look at the previous posts on where to see the firewall plug. Its near the fuse box
Pics just installed spyder oem fog lights on lx coupe
- Thread starter pssstitsmike
- Start date
NixSOCal
Well-Known Member
how about the fog light relay and the green?
- Thread starter
- #83
pssstitsmike
Well-Known Member
- 167
- 105
Make sure you buy the add a circuit to mini fuse to tap into accessory for the green wire. Other than that it is simply 2 black ground wires and white power wire goes to battery. Make sure you buy a terminal connector to hook it up to the battery. Good luck with the install. Takes about 3 hours from start to finish. The bumper is easy to remove. Its just 12 clips on the bottom 2 screws on each side near the tires and two screws on the grill n a few clips there
- Thread starter
- #84
pssstitsmike
Well-Known Member
- 167
- 105
this is where the green wire connects to.
nat3d
Wait, I don't drive a civic anymore....
hey did your fogs line right up in the bumper? i got mine off carid and they leave a gap around the shroud 
so i just threw the bumper back on and figured id post on here before i call carid c/s
here are the pics
so i just threw the bumper back on and figured id post on here before i call carid c/shere are the pics
Pauly99to17
Well-Known Member
I just ordered them. Been a while I have been thinking about it.
That gap is concerning.
That gap is concerning.
Last edited:
Pauly99to17
Well-Known Member
I have an LX sedan so I will need to cut holes too. Is it possible that you cut the holes in your bumper a touch too large?...or a touch too small?
Last edited:
Pauly99to17
Well-Known Member
Oh ya, easier for you guys with coupe.
nat3d
Wait, I don't drive a civic anymore....
if they line up lmao
- Staff
- #92
- 52,105
- 22,314
He was online yesterday. pssstitsmike see a few posts up.
- Thread starter
- #93
pssstitsmike
Well-Known Member
- 167
- 105
Mine has a slight gap as well but yours seems more noticable
- Thread starter
- #94
pssstitsmike
Well-Known Member
- 167
- 105
- Thread starter
- #95
pssstitsmike
Well-Known Member
- 167
- 105
the gaps doenst bother me though. U have to be super close to it to notice it. I like the fog lights even with the gap. A lot cheaper than the oem honda fogs
Pauly99to17
Well-Known Member
Got mine in the mail. Button feels a little cheap. Does it look and feel okay once in the slot?
Did you keep the bulbs that are already in the lights? How are they? I will guess not so good and probably cheap and won't last long. ????
If I order bulbs, I'm looking for plug and play. I would like them to be white with a blueish shade to them.....say 7000k - 8000k. Anyone have a suggestion of which bulbs to order......if I even need to. Appreciate any help you can give.
Did you keep the bulbs that are already in the lights? How are they? I will guess not so good and probably cheap and won't last long. ????
If I order bulbs, I'm looking for plug and play. I would like them to be white with a blueish shade to them.....say 7000k - 8000k. Anyone have a suggestion of which bulbs to order......if I even need to. Appreciate any help you can give.
Last edited:
CivicCanuck
Well-Known Member
Looking at the pictures again, it may be possible to slightly enlarge the screw hole and push the garnish up slightly while tightening the screw to hold it at a higher position to conceal the gap a bit better.
- Thread starter
- #99
pssstitsmike
Well-Known Member
- 167
- 105
The button is just fine. To get 7000k or 8000k color u need hids.
Pauly99to17
Well-Known Member
Are you using the bulbs that came with them?